SkyNozzle Pack — Drone Cleaning Nozzle Set | WasherDrone

SkyTips is a four-piece stainless steel nozzle set for drone-based exterior cleaning. It covers the full working range an operator meets on a façade — from a concentrated jet for stubborn deposits to a wide, low-impact rinse for glass and solar panels. All four nozzles share the same size 04 orifice and the same 1/4” quick-connect fitting, so flow stays consistent across the set and a change-over takes seconds with no tools. SkyTips fits the SkyLance M400 airborne lance, the SkyGun, WasherDrone ground pump units, and any third-party lance or gun using the 1/4” quick-connect standard.

Key benefits

• Full working range. 0°, 15°, 25° and 40° cover spot removal, chiselling, general cleaning and wide rinsing.
• Consistent flow. All four nozzles are size 04, so swapping angles does not change system flow or force a pump re-check.
• Seconds to change. 1/4” quick-connect plugs — no spanners, no thread sealing, no downtime on the roof.
• Read at a glance. Industry-standard colour coding: red 0°, yellow 15°, green 25°, white 40°.
• Corrosion resistant. Stainless steel construction for outdoor work and repeated exposure to water and cleaning solutions.
• Cross-system fit. Works with the SkyLance M400, the SkyGun, WasherDrone ground pump units and third-party 1/4” quick-connect equipment.

How it works

Each nozzle is a stainless steel spray tip on a 1/4” quick-connect plug. The operator selects the angle that suits the surface and the soiling, pushes the nozzle into the coupler on the lance or gun, and releases the collar to lock it. Because every nozzle in the set carries the same size 04 orifice, flow through the system stays the same whichever angle is fitted.

1. Select: Pick the spray angle for the surface — narrow for spot work, wide for rinsing.
2. Connect: Push the nozzle into the 1/4” quick-connect coupler and release the collar.
3. Spray: Work the surface, then swap angles as the job changes — no tools required.

Specifications

Models

• SkyTips — complete set — WD-NZL-01 (All four nozzles: 0°, 15°, 25° and 40°. The standard field kit.)
• 0° red — spot — WD-NZL-01-00 (Concentrated jet for localised deposits. Controlled short-range work; see operating notes.)
• 15° yellow — chisel — WD-NZL-01-15 (Narrow, high-impact fan for heavy soiling on robust surfaces such as concrete and stone.)
• 25° green — general — WD-NZL-01-25 (The everyday façade angle — the usual first choice for mixed exterior surfaces.)
• 40° white — rinse — WD-NZL-01-40 (Wide, low-impact fan for glass, painted surfaces, solar panels and final rinsing.)

What’s included

• 0° red spot nozzle
• 15° yellow chisel nozzle
• 25° green general-purpose nozzle
• 40° white rinse nozzle

Before you deploy

0° nozzle — use with care. The 0° red nozzle concentrates the full working pressure onto a point. It can mark or damage glass, paint, sealants and panel surfaces, and its reaction force is the highest of the four. It is intended for controlled spot work at short range, not for general airborne façade cleaning. Assess the surface first.

Match the nozzle to the pump. Nozzle size determines the pressure a given pump develops. SkyTips is supplied in size 04; confirm this suits your pump before first use.

Consumable. Nozzles wear with use. A worn orifice loses pressure and spray definition — replace individual nozzles rather than the whole set.

Check before you fly. Confirm the nozzle is fully seated and the quick-connect collar is locked before every flight. Carry the spares you expect to need; a change-over at height is not possible.

Component supply. SkyTips is supplied as a component for integration into WasherDrone systems. Conformity of the complete cleaning system is covered by that system’s own documentation.

After use. Flush with clean water after working with cleaning solutions, and store dry.

Shipping and customs duties are not included.